Implement dynamic MCS selection based on signal strength in vWIFI driver

This commit enhances the vWIFI driver by implementing
dynamic Modulation and Coding Scheme (MCS) selection in
the `vwifi_get_station` function, adjusting the MCS index
based on signal strength

After implement dynamic MCS can avoid TX power waste for
a bad channel quality

Author: dingsen-Greenhorn

vwifi.c

@@ -1403,8 +1403,19 @@ static int vwifi_get_station(struct wiphy *wiphy,
     sinfo->tx_failed = vif->stats.tx_dropped;
     sinfo->tx_bytes = vif->stats.tx_bytes;
     sinfo->rx_bytes = vif->stats.rx_bytes;
+
+
+    /* Log byte counters for debugging */ /* CHANGED */
+    pr_info(
+        "vwifi: Station %pM tx_bytes %llu, rx_bytes %llu, tx_packets %u, "
+        "rx_packets %u, tx_failed %u\n",
+        mac, sinfo->tx_bytes, sinfo->rx_bytes, sinfo->tx_packets,
+        sinfo->rx_packets, sinfo->tx_failed);
+
     /* For CFG80211_SIGNAL_TYPE_MBM, value is expressed in dBm */
     sinfo->signal = rand_int_smooth(-100, -30, jiffies);
+    pr_info("vwifi: Station %pM signal %d dBm (raw)\n", mac,
+            sinfo->signal); /* ADDED */
     sinfo->inactive_time = jiffies_to_msecs(jiffies - vif->active_time);
     /*
      * Using 802.11n (HT) as the PHY, configure as follows:
@@ -1425,18 +1436,58 @@ static int vwifi_get_station(struct wiphy *wiphy,
      * https://semfionetworks.com/blog/mcs-table-updated-with-80211ax-data-rates/
      * IEEE 802.11n : https://zh.wikipedia.org/zh-tw/IEEE_802.11n
      */
-    sinfo->rxrate.flags |= RATE_INFO_FLAGS_MCS;
-    sinfo->rxrate.mcs = 31;
+
+
+
+    /* Log byte counters for debugging */
+    pr_info("vwifi: Station %pM tx_bytes %llu, rx_bytes %llu\n", mac,
+            sinfo->tx_bytes, sinfo->rx_bytes);
+
+    /* Dynamic modulation based on signal strength */
+    int mcs_index;
+    const char *modulation;
+    unsigned int data_rate_mbps;
+    if (sinfo->signal > -50) {
+        /* Strong signal: 64-QAM, MCS 31 */
+        mcs_index = 31;
+        modulation = "64-QAM";
+    } else if (sinfo->signal > -70 && sinfo->signal <= -50) {
+        /* Medium signal: 16-QAM, MCS 23 */
+        mcs_index = 23;
+        modulation = "16-QAM";
+    } else if (sinfo->signal > -90 && sinfo->signal <= -70) {
+        /* Weak signal: QPSK, MCS 15 */
+        mcs_index = 15;
+        modulation = "QPSK";
+    } else {
+        /* Very weak signal: BPSK, MCS 7 */
+        mcs_index = 7;
+        modulation = "BPSK";
+    }
+
+    /* Log signal, modulation, and data rate for debugging */
+    pr_info(
+        "vwifi: Station %pM signal %d dBm, using modulation %s (MCS %d, %u "
+        "Mbps)\n",
+        mac, sinfo->signal, modulation, mcs_index, data_rate_mbps);
+
+    /* Configure RX and TX rates */
+    sinfo->rxrate.flags = RATE_INFO_FLAGS_MCS;
+    sinfo->rxrate.mcs = mcs_index;
     sinfo->rxrate.bw = RATE_INFO_BW_20;
     sinfo->rxrate.n_bonded_ch = 1;
 
-    sinfo->txrate.flags |= RATE_INFO_FLAGS_MCS;
-    sinfo->txrate.mcs = 31;
+    sinfo->txrate.flags = RATE_INFO_FLAGS_MCS;
+    sinfo->txrate.mcs = mcs_index;
     sinfo->txrate.bw = RATE_INFO_BW_20;
     sinfo->txrate.n_bonded_ch = 1;
+
+    /* Log rate configuration for verification */
+    pr_info("vwifi: Station %pM txrate MCS %d, rxrate MCS %d\n", mac,
+            sinfo->txrate.mcs, sinfo->rxrate.mcs);
+
     return 0;
 }
-
 /* dump station callback -- resume dump at index @idx */
 static int vwifi_dump_station(struct wiphy *wiphy,
                               struct net_device *dev,
@@ -2178,23 +2229,26 @@ static struct cfg80211_ops vwifi_cfg_ops = {
 };
 
 /* Macro for defining 2GHZ channel array */
-#define CHAN_2GHZ(channel, freq)                          \
-    {                                                     \
-        .band = NL80211_BAND_2GHZ, .hw_value = (channel), \
-        .center_freq = (freq),                            \
+#define CHAN_2GHZ(channel, freq)   \
+    {                              \
+        .band = NL80211_BAND_2GHZ, \
+        .hw_value = (channel),     \
+        .center_freq = (freq),     \
     }
 
 /* Macro for defining 5GHZ channel array */
-#define CHAN_5GHZ(channel)                                \
-    {                                                     \
-        .band = NL80211_BAND_5GHZ, .hw_value = (channel), \
-        .center_freq = 5000 + (5 * (channel)),            \
+#define CHAN_5GHZ(channel)                     \
+    {                                          \
+        .band = NL80211_BAND_5GHZ,             \
+        .hw_value = (channel),                 \
+        .center_freq = 5000 + (5 * (channel)), \
     }
 
 /* Macro for defining rate table */
-#define RATE_ENT(_rate, _hw_value)                   \
-    {                                                \
-        .bitrate = (_rate), .hw_value = (_hw_value), \
+#define RATE_ENT(_rate, _hw_value) \
+    {                              \
+        .bitrate = (_rate),        \
+        .hw_value = (_hw_value),   \
     }
 
 /* Array of "supported" channels in 2GHz band. It is required for wiphy. */