enetc: Introduce basic PF and VF ENETC ethernet drivers

ENETC is a multi-port virtualized Ethernet controller supporting GbE
designs and Time-Sensitive Networking (TSN) functionality.
ENETC is operating as an SR-IOV multi-PF capable Root Complex Integrated
Endpoint (RCIE).  As such, it contains multiple physical (PF) and
virtual (VF) PCIe functions, discoverable by standard PCI Express.

Introduce basic PF and VF ENETC ethernet drivers.  The PF has access to
the ENETC Port registers and resources and makes the required privileged
configurations for the underlying VF devices.  Common functionality is
controlled through so called System Interface (SI) register blocks, PFs
and VFs own a SI each.  Though SI register blocks are almost identical,
there are a few privileged SI level controls that are accessible only to
PFs, and so the distinction is made between PF SIs (PSI) and VF SIs (VSI).
As such, the bulk of the code, including datapath processing, basic h/w
offload support and generic pci related configuration, is shared between
the 2 drivers and is factored out in common source files (i.e. enetc.c).

Major functionalities included (for both drivers):
MSI-X support for Rx and Tx processing, assignment of Rx/Tx BD ring pairs
to MSI-X entries, multi-queue support, Rx S/G (Rx frame fragmentation) and
jumbo frame (up to 9600B) support, Rx paged allocation and reuse, Tx S/G
support (NETIF_F_SG), Rx and Tx checksum offload, PF MAC filtering and
initial control ring support, VLAN extraction/ insertion, PF Rx VLAN
CTAG filtering, VF mac address config support, VF VLAN isolation support,
etc.

Signed-off-by: Claudiu Manoil <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

Author: claudiu-m

MAINTAINERS

@@ -6023,6 +6023,12 @@ L:	[email protected]
 S:	Maintained
 F:	drivers/dma/fsldma.*
 
+FREESCALE ENETC ETHERNET DRIVERS
+M:	Claudiu Manoil <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	drivers/net/ethernet/freescale/enetc/
+
 FREESCALE eTSEC ETHERNET DRIVER (GIANFAR)
 M:	Claudiu Manoil <[email protected]>
 L:	[email protected]

drivers/net/ethernet/freescale/Kconfig

@@ -97,5 +97,6 @@ config GIANFAR
 
 source "drivers/net/ethernet/freescale/dpaa/Kconfig"
 source "drivers/net/ethernet/freescale/dpaa2/Kconfig"
+source "drivers/net/ethernet/freescale/enetc/Kconfig"
 
 endif # NET_VENDOR_FREESCALE

drivers/net/ethernet/freescale/Makefile

@@ -23,3 +23,6 @@ obj-$(CONFIG_FSL_FMAN) += fman/
 obj-$(CONFIG_FSL_DPAA_ETH) += dpaa/
 
 obj-$(CONFIG_FSL_DPAA2_ETH) += dpaa2/
+
+obj-$(CONFIG_FSL_ENETC) += enetc/
+obj-$(CONFIG_FSL_ENETC_VF) += enetc/

drivers/net/ethernet/freescale/enetc/Kconfig

@@ -0,0 +1,19 @@
+# SPDX-License-Identifier: GPL-2.0
+config FSL_ENETC
+	tristate "ENETC PF driver"
+	depends on PCI && PCI_MSI && (ARCH_LAYERSCAPE || COMPILE_TEST)
+	help
+	  This driver supports NXP ENETC gigabit ethernet controller PCIe
+	  physical function (PF) devices, managing ENETC Ports at a privileged
+	  level.
+
+	  If compiled as module (M), the module name is fsl-enetc.
+
+config FSL_ENETC_VF
+	tristate "ENETC VF driver"
+	depends on PCI && PCI_MSI && (ARCH_LAYERSCAPE || COMPILE_TEST)
+	help
+	  This driver supports NXP ENETC gigabit ethernet controller PCIe
+	  virtual function (VF) devices enabled by the ENETC PF driver.
+
+	  If compiled as module (M), the module name is fsl-enetc-vf.

drivers/net/ethernet/freescale/enetc/Makefile

@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_FSL_ENETC) += fsl-enetc.o
+fsl-enetc-$(CONFIG_FSL_ENETC) += enetc.o enetc_cbdr.o enetc_ethtool.o
+fsl-enetc-objs := enetc_pf.o $(fsl-enetc-y)
+
+obj-$(CONFIG_FSL_ENETC_VF) += fsl-enetc-vf.o
+
+ifeq ($(CONFIG_FSL_ENETC)$(CONFIG_FSL_ENETC_VF), yy)
+fsl-enetc-vf-objs := enetc_vf.o
+else
+fsl-enetc-vf-$(CONFIG_FSL_ENETC_VF) += enetc.o enetc_cbdr.o \
+				       enetc_ethtool.o
+fsl-enetc-vf-objs := enetc_vf.o $(fsl-enetc-vf-y)
+endif