Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2019-03-02

Here's one more bluetooth-next pull request for the 5.1 kernel:

 - Added support for MediaTek MT7663U and MT7668U UART devices
 - Cleanups & fixes to the hci_qca driver
 - Fixed wakeup pin behavior for QCA6174A controller

Please let me know if there are any issues pulling. Thanks.
====================

Signed-off-by: David S. Miller <[email protected]>

Author: davem330

Documentation/devicetree/bindings/net/btusb.txt

@@ -9,6 +9,9 @@ Required properties:
 		 (more may be added later) are:
 
 		  "usb1286,204e" (Marvell 8997)
+		  "usbcf3,e300" (Qualcomm QCA6174A)
+		  "usb4ca,301a" (Qualcomm QCA6174A (Lite-On))
+
 
 Also, vendors that use btusb may have device additional properties, e.g:
 Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt

Documentation/devicetree/bindings/net/mediatek-bluetooth.txt

@@ -33,3 +33,67 @@ Example:
 			clock-names = "ref";
 		};
 	};
+
+MediaTek UART based Bluetooth Devices
+==================================
+
+This device is a serial attached device to UART device and thus it must be a
+child node of the serial node with UART.
+
+Please refer to the following documents for generic properties:
+
+	Documentation/devicetree/bindings/serial/slave-device.txt
+
+Required properties:
+
+- compatible:	Must be
+		  "mediatek,mt7663u-bluetooth": for MT7663U device
+		  "mediatek,mt7668u-bluetooth": for MT7668U device
+- vcc-supply:	Main voltage regulator
+- pinctrl-names: Should be "default", "runtime"
+- pinctrl-0: Should contain UART RXD low when the device is powered up to
+	     enter proper bootstrap mode.
+- pinctrl-1: Should contain UART mode pin ctrl
+
+Optional properties:
+
+- reset-gpios:	GPIO used to reset the device whose initial state keeps low,
+		if the GPIO is missing, then board-level design should be
+		guaranteed.
+- current-speed:  Current baud rate of the device whose defaults to 921600
+
+Example:
+
+	uart1_pins_boot: uart1-default {
+		pins-dat {
+			pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>;
+			output-low;
+		};
+	};
+
+	uart1_pins_runtime: uart1-runtime {
+		pins-dat {
+			pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>,
+				 <MT7623_PIN_82_UTXD1_FUNC_UTXD1>;
+		};
+	};
+
+	uart1: serial@11003000 {
+		compatible = "mediatek,mt7623-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0 0x11003000 0 0x400>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_UART1_SEL>,
+			 <&pericfg CLK_PERI_UART1>;
+		clock-names = "baud", "bus";
+
+		bluetooth {
+			compatible = "mediatek,mt7663u-bluetooth";
+			vcc-supply = <&reg_5v>;
+			reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default", "runtime";
+			pinctrl-0 = <&uart1_pins_boot>;
+			pinctrl-1 = <&uart1_pins_runtime>;
+			current-speed = <921600>;
+		};
+	};

arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi

@@ -200,6 +200,19 @@
 		pinctrl-0 = <&bl_en>;
 		pwm-delay-us = <10000>;
 	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l>;
+
+		wake_on_bt: wake-on-bt {
+			label = "Wake-on-Bluetooth";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
 };
 
 &ppvar_bigcpu {

arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi

@@ -175,6 +175,21 @@
 		pinctrl-0 = <&dmic_en>;
 		wakeup-delay-ms = <250>;
 	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pen_eject_odl>;
+
+		pen-insert {
+			label = "Pen Insert";
+			/* Insert = low, eject = high */
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_PEN_INSERTED>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+	};
 };
 
 /* pp900_s0 aliases */
@@ -328,20 +343,6 @@ camera: &i2c7 {
 		<400000000>;
 };
 
-&gpio_keys {
-	pinctrl-names = "default";
-	pinctrl-0 = <&bt_host_wake_l>, <&pen_eject_odl>;
-
-	pen-insert {
-		label = "Pen Insert";
-		/* Insert = low, eject = high */
-		gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-		linux,code = <SW_PEN_INSERTED>;
-		linux,input-type = <EV_SW>;
-		wakeup-source;
-	};
-};
-
 &i2c_tunnel {
 	google,remote-bus = <0>;
 };
@@ -437,8 +438,19 @@ camera: &i2c7 {
 	status = "okay";
 };
 
-&wake_on_bt {
-	gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+&usb_host0_ohci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	qca_bt: bluetooth@1 {
+		compatible = "usbcf3,e300", "usb4ca,301a";
+		reg = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "wakeup";
+	};
 };
 
 /* PINCTRL OVERRIDES */
@@ -455,7 +467,7 @@ camera: &i2c7 {
 };
 
 &bt_host_wake_l {
-	rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_up>;
+	rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_none>;
 };
 
 &ec_ap_int_l {

arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi

@@ -269,19 +269,6 @@
 		#clock-cells = <0>;
 	};
 
-	gpio_keys: gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&bt_host_wake_l>;
-
-		wake_on_bt: wake-on-bt {
-			label = "Wake-on-Bluetooth";
-			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			wakeup-source;
-		};
-	};
-
 	max98357a: max98357a {
 		compatible = "maxim,max98357a";
 		pinctrl-names = "default";