Merge tag 'tee-amdtee-fix-for-5.6' of https://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes

Fix AMDTEE memory leak in amdtee_open_session()

* tag 'tee-amdtee-fix-for-5.6' of https://git.linaro.org/people/jens.wiklander/linux-tee: (344 commits)
  tee: amdtee: fix memory leak in amdtee_open_session()
  Linux 5.6-rc2
  ext4: improve explanation of a mount failure caused by a misconfigured kernel
  Input: cyapa - replace zero-length array with flexible-array member
  Input: tca6416-keypad - replace zero-length array with flexible-array member
  Input: gpio_keys_polled - replace zero-length array with flexible-array member
  IB/mlx5: Use div64_u64 for num_var_hw_entries calculation
  nvme: fix the parameter order for nvme_get_log in nvme_get_fw_slot_info
  nvme/pci: move cqe check after device shutdown
  nvme: prevent warning triggered by nvme_stop_keep_alive
  nvme/tcp: fix bug on double requeue when send fails
  cifs: make sure we do not overflow the max EA buffer size
  cifs: enable change notification for SMB2.1 dialect
  netdevice.h: fix all kernel-doc and Sphinx warnings
  net: dsa: tag_ar9331: Make sure there is headroom for tag
  net: dsa: tag_qca: Make sure there is headroom for tag
  net, ip6_tunnel: enhance tunnel locate with link check
  net/smc: no peer ID in CLC decline for SMCD
  net/smc: transfer fasync_list in case of fallback
  net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()
  ...

Link: https://lore.kernel.org/r/20200227165205.GA7926@jade
Signed-off-by: Olof Johansson <[email protected]>

Author: olofj

Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt

@@ -1,9 +1,10 @@
-Ilitek ILI210x/ILI2117/ILI251x touchscreen controller
+Ilitek ILI210x/ILI2117/ILI2120/ILI251x touchscreen controller
 
 Required properties:
 - compatible:
     ilitek,ili210x for ILI210x
     ilitek,ili2117 for ILI2117
+    ilitek,ili2120 for ILI2120
     ilitek,ili251x for ILI251x
 
 - reg: The I2C address of the device

Documentation/driver-api/ipmb.rst

@@ -71,9 +71,13 @@ b) Example for device tree::
             ipmb@10 {
                     compatible = "ipmb-dev";
                     reg = <0x10>;
+                    i2c-protocol;
             };
      };
 
+If xmit of data to be done using raw i2c block vs smbus
+then "i2c-protocol" needs to be defined as above.
+
 2) Manually from Linux::
 
      modprobe ipmb-dev-int

Documentation/virtual/guest-halt-polling.txt renamed to Documentation/virt/guest-halt-polling.rst

@@ -1,9 +1,11 @@
+==================
 Guest halt polling
 ==================
 
 The cpuidle_haltpoll driver, with the haltpoll governor, allows
 the guest vcpus to poll for a specified amount of time before
 halting.
+
 This provides the following benefits to host side polling:
 
 	1) The POLL flag is set while polling is performed, which allows
@@ -29,25 +31,29 @@ Module Parameters
 The haltpoll governor has 5 tunable module parameters:
 
 1) guest_halt_poll_ns:
+
 Maximum amount of time, in nanoseconds, that polling is
 performed before halting.
 
 Default: 200000
 
 2) guest_halt_poll_shrink:
+
 Division factor used to shrink per-cpu guest_halt_poll_ns when
 wakeup event occurs after the global guest_halt_poll_ns.
 
 Default: 2
 
 3) guest_halt_poll_grow:
+
 Multiplication factor used to grow per-cpu guest_halt_poll_ns
 when event occurs after per-cpu guest_halt_poll_ns
 but before global guest_halt_poll_ns.
 
 Default: 2
 
 4) guest_halt_poll_grow_start:
+
 The per-cpu guest_halt_poll_ns eventually reaches zero
 in case of an idle system. This value sets the initial
 per-cpu guest_halt_poll_ns when growing. This can
@@ -66,13 +72,13 @@ high once achieves global guest_halt_poll_ns value).
 
 Default: Y
 
-The module parameters can be set from the debugfs files in:
+The module parameters can be set from the debugfs files in::
 
 	/sys/module/haltpoll/parameters/
 
 Further Notes
 =============
 
 - Care should be taken when setting the guest_halt_poll_ns parameter as a
-large value has the potential to drive the cpu usage to 100% on a machine which
-would be almost entirely idle otherwise.
+  large value has the potential to drive the cpu usage to 100% on a machine
+  which would be almost entirely idle otherwise.

Documentation/virt/index.rst

@@ -8,7 +8,9 @@ Linux Virtualization Support
    :maxdepth: 2
 
    kvm/index
+   uml/user_mode_linux
    paravirt_ops
+   guest-halt-polling
 
 .. only:: html and subproject