Revert "tty: serial: Use fifo in 8250 console driver"

This reverts commit 5021d70.

The patch is still a bit buggy, and this breaks some other hardware
types.  It needs to be resubmitted in a non-buggy way, and make sure the
other hardware types also continue to work properly.

Fixes: 5021d70 ("tty: serial: Use fifo in 8250 console driver")
Reported-by: Sebastian Andrzej Siewior <[email protected]>
Reported-by: Jon Hunter <[email protected]>
Link: https://lore.kernel.org/r/Ye/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Cc: Wander Lairson Costa <[email protected]>
Cc: Andy Shevchenko <[email protected]>
Cc: Jiri Slaby <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

Author: gregkh

drivers/tty/serial/8250/8250_port.c

@@ -2056,7 +2056,10 @@ static void serial8250_break_ctl(struct uart_port *port, int break_state)
 	serial8250_rpm_put(up);
 }
 
-static void wait_for_lsr(struct uart_8250_port *up, int bits)
+/*
+ *	Wait for transmitter & holding register to empty
+ */
+static void wait_for_xmitr(struct uart_8250_port *up, int bits)
 {
 	unsigned int status, tmout = 10000;
 
@@ -2073,16 +2076,6 @@ static void wait_for_lsr(struct uart_8250_port *up, int bits)
 		udelay(1);
 		touch_nmi_watchdog();
 	}
-}
-
-/*
- *	Wait for transmitter & holding register to empty
- */
-static void wait_for_xmitr(struct uart_8250_port *up, int bits)
-{
-	unsigned int tmout;
-
-	wait_for_lsr(up, bits);
 
 	/* Wait up to 1s for flow control if necessary */
 	if (up->port.flags & UPF_CONS_FLOW) {
@@ -3332,35 +3325,6 @@ static void serial8250_console_restore(struct uart_8250_port *up)
 	serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
 }
 
-/*
- * Print a string to the serial port using the device FIFO
- *
- * It sends fifosize bytes and then waits for the fifo
- * to get empty.
- */
-static void serial8250_console_fifo_write(struct uart_8250_port *up,
-					  const char *s, unsigned int count)
-{
-	int i;
-	const char *end = s + count;
-	unsigned int fifosize = up->port.fifosize;
-	bool cr_sent = false;
-
-	while (s != end) {
-		wait_for_lsr(up, UART_LSR_THRE);
-
-		for (i = 0; i < fifosize && s != end; ++i) {
-			if (*s == '\n' && !cr_sent) {
-				serial_out(up, UART_TX, '\r');
-				cr_sent = true;
-			} else {
-				serial_out(up, UART_TX, *s++);
-				cr_sent = false;
-			}
-		}
-	}
-}
-
 /*
  *	Print a string to the serial port trying not to disturb
  *	any possible real use of the port...
@@ -3376,7 +3340,7 @@ void serial8250_console_write(struct uart_8250_port *up, const char *s,
 	struct uart_8250_em485 *em485 = up->em485;
 	struct uart_port *port = &up->port;
 	unsigned long flags;
-	unsigned int ier, use_fifo;
+	unsigned int ier;
 	int locked = 1;
 
 	touch_nmi_watchdog();
@@ -3408,20 +3372,7 @@ void serial8250_console_write(struct uart_8250_port *up, const char *s,
 		mdelay(port->rs485.delay_rts_before_send);
 	}
 
-	use_fifo = (up->capabilities & UART_CAP_FIFO) &&
-		port->fifosize > 1 &&
-		(serial_port_in(port, UART_FCR) & UART_FCR_ENABLE_FIFO) &&
-		/*
-		 * After we put a data in the fifo, the controller will send
-		 * it regardless of the CTS state. Therefore, only use fifo
-		 * if we don't use control flow.
-		 */
-		!(up->port.flags & UPF_CONS_FLOW);
-
-	if (likely(use_fifo))
-		serial8250_console_fifo_write(up, s, count);
-	else
-		uart_console_write(port, s, count, serial8250_console_putchar);
+	uart_console_write(port, s, count, serial8250_console_putchar);
 
 	/*
 	 *	Finally, wait for transmitter to become empty